rjts

MEMBERS
  • Content count

    55
  • Joined

  • Last visited

About rjts

  • Rank
    BREAM
  • Birthday 05/25/1976

Profile Information

  • Gender
    Male
  • Location
    gwandalan

Recent Profile Visitors

266 profile views
  1. You can use sheet lead(fold it etc). YoZuri skirts are one of the thinner ones,alot of Yozuri's don't fold well around the skirt saddle creating a lump & their to short for their width for a lot of lures.Yamashitas are thinner.
  2. See the fake Evil Apollo on E bay at the moment, $330 with a day to go one of those poor fools is going to get ripped off.
  3. A black mop shell copy of that blue Apollo,larger ones are 501s.
  4. Ebay,just make sure you check the mm as the majority are for squid jigs etc.Or buy a hole punch/circle cutter.
  5. Theirs been a few caught Sealy (Bombo) late last week
  6. Does anyone know an Aus tackle dealer that stocks 3/16 white plastic tubing in length (by the meter etc) not in 1cm strips. Cheers.
  7. What type of hook are you using
  8. The red tape I used for eyes in this green Mcgoo looks to have somehow turned silver,if anyone has a theory,it's got me stuffed.Also in regards to brass tubing damaging line,I discovered you can make lead inserts with plastic tubing instead,like in this Streamline..After pouring a insert you just lightly tap the brass tube with a hammer & the brass tubing twists out of the lead...Ps- Vvickid I like that bullet,was the mold taken off a BlkBrt master?.
  9. Start with low grit, then med,end with 1200-2000 &then polish
  10. It's more stuffing round but start with 360-600 then 800 & so on to 2000 it comes up great.Using 1200 first will clog etc real quick
  11. Like amkr said it comes off when lathing/polishing.I've tried diggers but prefer the clear casting resin Barnes have,it pours clear so it's easier to keep track of the pigments dye/pearl powder etc.Avoid the equal part resins like Alumilite etc,they go dull with wet&dry paper & take forever to cure.I've been trying out some uv powders & ab shell.These are jy Apollos & Mcgoo chuggers.
  12. Both,-heat res rtv silicone(sim to ultra copper you use for engine gaskets) for lead mold.Adding a piece of lead the thickness of a pen etc to the lower 1/2 of insert (like JYee does in Apollo's etc) works great.So does adding uv/lumo pearl powder like this Magoo insert.
  13. No I don't but I'm still far from having it perfected so I may have to.I've ordered a Dremel tool which I've been told will make it a lot easier.All the saws,grinders & drill bits various Hardware,Model shops,engineering stores etc have told me will do the job have failed,so if the dremel doesn't work I'm going to give up on jetted lures to. I reckon all they seem to do is liven the skirt up & lighten the pull on flat faces a bit,but if the holes are less than 5-6mm they do nothing. I was hoping to make some slightly lighter keel weighted ones beause the yanks/Hawaiians either make them full of lead or none at all(1stpic) , The jetted plunger in the 2nd pic is keel weighted,nylon holes & doesn't need as much speed as the other jet heads.
  14. I only cut the length of the skirt saddles(photo angles misleading),but I've met blokes that cut the whole way down to the nose.I couldn't get tape to hold so a lightly tensioned band etc has been working well so far.Have been having a lot of trial & error with inserts,mainly cutting & smoothing off brass tube for jets etc.