Jump to content

BWV

MEMBER
  • Posts

    243
  • Joined

  • Last visited

1 Follower

Profile Information

  • Location
    Cronulla

Recent Profile Visitors

927 profile views

BWV's Achievements

WHITING

WHITING (6/19)

0

Reputation

  1. It’s low, your antiventilation plate (bottom plate)should be clear of the water when planning, and only getting splashed. Engines revs will increase as engine is raised as load is reduced. Do a search on this topic, it’s been covered before.
  2. They are illegal, so much more goes into the navigation light other than being red, green or white. Lights give specific angles and luminosity to aid in collision avoidance at night and if they don't display the correct angle your asking for trouble.
  3. BWV

    Motor Height

    Ok guys, it's a antiventilation plate, not a cavitation plate! Your AV plate should only be getting splashed when running, not in the water. Your engine rpm's will increase as height is increased, as drag is reduced, therefore load is reduced allowing the engine to operate with less load and more efficiency. You want your RPM's 200rpm off the manufacturers stated maximum rpm, eg if max is 6000rpm you want 5800rpm loaded. This will give you the best all round proformance and longevity of your outboard. If you feel the need to bolt any foils, permatrims etc to your outboard something else is wrong. They only hide the symptoms of other problems and increase drag. This topic has been done to death on all forums but there is so much wrong information out there because a friend of a friend said to do this or that, be careful which info you choose to run with because you'll end up in trouble. FYI, every outboard powered boat I have owned I have lifted the engine and on all of my friends boats we have lifted the engines. They are all mounted low.
  4. BWV

    Prop Selection

    Your under reving, if your rev range is 5000/5500-6000rpm you want it reving at 5800rpm under normal load at full power, at 5800rpm you'll have the best balance between engine load, speed and efficiency. You should always aim for 200rpm less than the stated maximum figure that under normal load so when light you won't exceed the maximum revs for your engine. On the flip side overloading your engine, as in not be able to achieve the given rev range will do just as much damage to the engine. For engine height, you want you antiventilation plate getting splashed by the spay not dragging though the water, every boat I have ever seen that is new has the engine mounted far too low.
  5. Got to be in water to get a reading.
  6. I would be using Marine Grade Ply that is stamped BS1080 or better, it's a Lloyds approved boat building ply.Epoxy + fibreglass mat on timber hull is strong as any boat building material out there and have half the weight of production boat for the same strength. I would be building the cabin out of ply the wetting it out with epoxy to seal the timber and then coating it in epoxy and fibreglass mat and the cabin will last for years to come, the finish you want will depend on how much sanding and filling you want to do. The fibreglass mat will become clear when wetted out with epoxy and stay clear. Don't be stingy with the epoxy as you will have voids in the glass. Are you familiar the the construction method "cold molding"? If not I suggest you read the relevant parts of the Gougeon Brothers on Boat Construction book, that will explain everything you could ever want. Also DO NOT stain any of the timber or put anything else on it for that matter prior to applying the epoxy and fibreglass. Just aim to encapsulate all timbers in epoxy. Epoxy if far more durable than varnish. But to get the old ski boat varnish look if that's what your after they have somewhere between 80-90 coats of varnish! Rushing to write this with 2 screaming kids so if it is some what confusing I apologise in advance.
  7. The only real way is to have the fuel polished, tanks and lines cleaned. Additives do work to a certain degree but become extremely expensive for large amounts of fuel. It's relatively east to rig up a polishing system onboard if you want to go down that path if you have more than one tank. Going through the same problem as we speak on a delivery to QLD only getting about 20 mins between filter changes on both main engines. Boat is now at Port Hacking waiting to get fuel and a few other problems rectified. If you want an additive to lubricate injectors and pumps etc due to the ultra low sulphur fuels your best bet is mineral 2 stroke outboard oil at 200:1, works extremely well and is miles ahead in price compared to other additives if bought in large amounts.
  8. not correct, the prop size sounds about right, give or take. it could be numerous things but start simple and connect it is another fuel source. Check linkages. Check filters and fuel line, it maybe starved of fuel under load. Electrical problems usually happens at all revs but not always.
  9. Check with the boat manufacturer, they will specify either roller or bunks and if you use the wrong one you will loose any hull warranty. They may say it doesn't matter. Rollers for GRP boats and bunks for alloy is BS, but loading points are critical.
  10. 75-115hp outboards are extremely difficult to come by second hand, nearly everyone wants them so you'll be paying nearly brand new prices for a relatively new second hand 90hp. Not saying it won't happen but have been down this path before, it was frustrating to say the least.
  11. Leave it bare, aluminium naturally oxidises and that layer of oxidisation that forms will provide a protective barrier against the elements and protect the alloy under neath it. Down side is it can look ordinary. You can constantly polish the boat if you prefer to maintain a shine.
  12. Spent plenty of time in Tas, your boat will be fine. Id rather fibreglass in just about any conditions especially in a place that gets so f¥€keen cold.
  13. Ive got used 1.5 tonne axles, hubs, bearings, u bolts and fishplates in good nick too. Pm me if your interested.
  14. BWV

    Boat safety rules

    By definition "underway" means, that a vessel is not at anchor, or made fast to the shore, or aground. Correct whilst drifting you are considered to be underway and must obey the Collision regs.We have become such a nanny state where they feel they to regulate us to the point that anything other than sitting in the boat will become an offence. It's frustrating that common sense no longer applies to anything, just introduce more legislation to turn everybody into a robot or fine them if they don't comply. This reminds me of the Kerry Packer response into the senate inquiry corporate tax evasion, if you want to introduce more legislation, repeal an out dated one first.
×
×
  • Create New...