Jump to content

spence

MEMBER
  • Posts

    68
  • Joined

  • Last visited

Everything posted by spence

  1. Any meat in it though, the last couple i have picked up have felt very light and have let them go....interesting to see whether it's full or not. mine were in sydney and water bit cold
  2. If the bungs aren't in and you can get on the plane a lot of the water will come out (haven't done this myself though - but have heard this from a couple of people).
  3. thanks for that guys I will have a look around
  4. Hello all, I am looking to buy a set of waders. I fish in Sydney, all year round, including winter (usually from my tinnie). I have found my myself doing a lot of land-based fishing lately and would like a set of waders to wade into weed beds etc at places like Narrabeen lake. I don't know anything about them other than what I have read on the net and I thought some other fishraiders honest advice would be better, thanks rod
  5. Love using "cobwebs" - makes every fish a good fight.....
  6. Hi blue bottle, out of interest, where do you fish at Lanecove, I drive thru lanecove a bit and always look at the water and see small swirls, and I've always wondered what it holds and whether you can fish in there, I've never seen anyone fishing it?, thanks Rod
  7. Just done my wheel bearings and the old dust covers have had it. The old ones were siliconed onto the wheel hub. I bought a set of bearing protectors with grease nipple. The diameter is way smaller than the old dust covers which I had siliconed to the hub. It appears as though you knock these protectors straight over the bearings. Is this right? It would mean there is an opening between the outside of the hub and the protectors
  8. Unfornately I find this happens all the time.......... I sometimes used to float my nets with clear bottles but worried about someone running over them and getting the rope around the prop. I like to stay nearby now, can't tell you how many times lost nets and crabs
  9. Does anyone know if there are any crabbing restrictions in middle harbour
  10. Mate the middle harbour has plenty of poddies, no need to go to narrabeen from there....shallow bays and boat ramps (hard on busy days) - got heaps of perfect poddies on saturday from a small bay - no flatties but got some squid.
  11. Thanks for that, yeah it is a big improvement, very easy to fish out of....come over and say hello next time
  12. no worries, thanks for that
  13. I need to replace my leaf springs before they break in half from corrosion. It is a small trailer for 3 - 4 metre tinnie, I haven't done it before, but had a look and it doesn't look that hard. Has anyone got any suggestions re where to get replacement springs from and whether it is straight forward. thanks spence
  14. Can any body tell me where to get some new springs for my trailer in the Sydney (western suburbs or northern beaches area preferrably) area. It is for a 385 quintrex. I'll probably fit them myself - thanks rod
  15. Baz, the steering wheel and throttle took up too much room on a small tinnie. 3 cables running front to back as well and it was after market, which didn't help - Forever mucking around with it. The tiller is heaps better. rod
  16. Yes on both questions. There is a small battery operated aerator that goes all the time and depends on what bait I have as to how long bait pump runs
  17. Boomer I've sent you a personal message
  18. great job mate.....i basically did the same thing last season on mine and i love it. the underfloor storage is awesome seeing as storage in a tinny is non existent. any chance of a photo of how u mounted the elec motor to the front grab rail? i plan on something similar in the following weeks. Here's photo's of elec motor front rear Steve Long thread countersunk to fit over first nut then wingnuts for easy removal to empty and clean. I have used this set up since last post and it works fine
  19. It feels good to make a nice float yourself or just buy them if you have a spare $1.50.
  20. Jewgaffer; the electric motor is a cheap one $200. It is a stern mount, but I have turned the handle around. I will take a picture and put it on, but am going away tomorrow morning for 4 days. Basically fitted a piece of plastic to the bow and bolted the electric straight on. It doesn't move or anything because the clamps are wedged under the rail. You will see what I mean when I put pictures on. I have had it for a few seasons without a hitch. It is only 32lb or something like that and medium shaft. The tinnie is only a punt and the motor still gets in the water...just. Evets, this was easy. The hatch is bolted to the aluminium angle. The lbt is screwed to a separate piece. The separate piece is bolted to the hatch - here I have used wingnuts for easy release. (It sits flat because I have countersunk underneath )
  21. Dave it is just a cheap water pump purchased locally - $50. Because it has such a short distance to pump it does it very easily, it comes out just like a hose and makes a good splash, circulating the water enough to keep poddies, yellow tail and squid alive
  22. After recently having remote steering replaced with a tiller I started to remove the steering wheel and cables....just kept going and stripped boat clean. It was past time for a new fit out; Wiring stripped out and new terminals/plugs for nav lights. Wiring for nav lights, sounder and electric motor run through conduit; Cut some aluminium box tube and angle and had box tube welded in on ribs and I pop riveted angle over them. Angle welded at the stern and more pop riveted to back of rear seat; flooring from 15mmm ply which was coated with waterproofing and carpeted; Then I cut front casting platforms- they are split in two and I had to move the sounder up under bow with switch for nav lights; - the flappy carpet on seat has now been glued down now cabin light wired up so now looks better than photo Then rear hatches cut and fitted (they house bucket, esky, battery and petrol tank); It came up well and looks like this; Then I re-fitted the old livie tank which works really well, but this time it is set well back in the boat. It doesn't hold too much water to affect boat. A switch is fitted (can't be seen in photo's) behind the tank. The hatch it sits on is bolted on and the livie tank is bolted to that hatch with wingnuts. It can easily be removed to empty/or clean; The band on the livie tank is just a headlite which I use as a stern light. The boat is an older 385 quintrex with 30hp honda. The aluminium is light. The ply replaced some older ply that was just screwed straight to ribs so no more than 20 - 30kg added. The under floor storage will house a hose/attachments and ropes etc. The costs were $200 for the welding, $60 for metal, $80 for the ply and $150 for carpet and $50 for glue. Waterproofing membrane I got for free. Other bits and pieces meant total cost of $600.
  23. I have a 10lb bomb and want to rig it up on my tinnie. I wouldn't use it often as I mainly fish for estaury fish but i do on occasion fish the harbour buoys and markers with livies. I was going to buy an Alvey reel but am wondering if it would be strong enough, I think it would have to be a large snapper Alvey which are expensive. AN alvey would be easy to attach to a rail on my boat. But I am now thinking of simply tying it off with some rope that I would mark every 5 metres. (I usually take a fishing partner in the harbour wo there a spare hands to pull it up). Any thoughts or anyone else who has done something like this would be helpful thanks rod.
  24. Hi all My family are looking at a caravan at Smiths Lake; it is at the eastern/northern side. I looked on sattelite view and the lake appears to be cut off from the sea. Is there any fishing (or crabbing) in that area? beach or lake? (we have a tinnie) I have fished and crabbed Wallis lake and it is one of my favorite spots but haven't heard of anyone fishing Smiths Lake. any info heaps appreciated - rod
  25. Don't think of squid as just bait either...keep some (green eyed squid) for the pan.....better than fish
×
×
  • Create New...